{"id":9394,"date":"2013-07-01T02:46:18","date_gmt":"2013-07-01T06:46:18","guid":{"rendered":"http:\/\/www.enxmag.com\/twii\/?p=9394"},"modified":"2014-11-03T02:56:27","modified_gmt":"2014-11-03T07:56:27","slug":"xerox-7120-style-fuser-modules","status":"publish","type":"post","link":"https:\/\/www.enxmag.com\/twii\/tech-tip\/2013\/07\/xerox-7120-style-fuser-modules\/","title":{"rendered":"Xerox 7120 style Fuser Modules"},"content":{"rendered":"

Xerox 7120 style Fuser Modules<\/strong>
\nRepairing and rebuilding the fusers for the WC-7120, 7125, 7220, 7225<\/strong><\/p>\n

\n

The WorkCentre 7120 series is a group of full color pure-bred Xerox machines which are worthy of our attention. These fellows share a lot of the basic design hallmarks of the 7425 style although they land on a slightly lower pricing level. As is usually the case, the fuser module is an important component which is pricy enough to warrant rebuilding. This fuser is slightly simpler than the 7425 fusers we covered in the past two articles, so I think we can tackle this topic in one article.<\/p>\n

\"\"<\/span><\/strong><\/span><\/p>\n<\/div>\n

\n

The 7120 fuser looks very similar to the 7425 style fuser at first glance, and the basic design is pretty close, at least in concept. If you\u2019ve read the 7425 fuser rebuild articles, this procedure will look familiar. In spite of the similar design however, the components don\u2019t cross over for the most part. For example, the Fuser Heat Roller is considerably shorter on the 7120.<\/p>\n

7120 style Fuser Module<\/strong><\/p>\n

The WorkCentre 7120 and 7125 were released first, and they are joined now by the newer WC-7220 and 7225 models. The fuser module which fits all 4 models is sold under the part number 008R13087 for the 110 volt version (overseas the 220 volt version is 008R13088). It has a stated yield of 80K according to some online sources although the OEM brochure doesn\u2019t say. Pricing online ranges between $350.00 and $500.00. The Fuser Heat Roller isn\u2019t spared in the OEM Parts Book, but thankfully some good compatible Fuser Heat Rollers have recently surfaced which make this fuser rebuildable.<\/p>\n

Let\u2019s get start by getting oriented– check out Photo #1. The \u201cRear End\u201d is the end with the Heat Roll Drive Gear and the main Fuser Connector. The \u201cOuter Face\u201d is the side which would face you if you were to walk up to the machine to remove the fuser and the \u201cInner Face\u201d is the opposite side. The \u201cTop\u201d is where you\u2019ll find the yellow Fuser Exit Guide.<\/p>\n

Now let\u2019s get right down to it.<\/p>\n

PROCEDURE:<\/strong><\/p>\n

1. First remove the \u201cOuter Cover,\u201d held on by two screws<\/strong>. You can use a 5.5 mm nut driver or #1 Philips Head. The screw near the front end also retains a small square cover; take that off now because it will fall off easily. Swing the yellow exit guide all the way open. As you jiggle the Outer Cover off, be gentle at the Rear End, because there are wires going to the Fuser Exit Sensor which is mounted on the Outer Cover (see Photo #2). You will need to raise the rear end off and disconnect the connector from that sensor.<\/p>\n

2. Then, remove the small rear end cover which also faces the \u201cOuter Face\u201d<\/strong> (one screw).<\/p>\n

3. Next flip the module over and take off the \u201cInner Cover\u201d <\/strong>(three screws – refer to Photo #3). Watch out–near the front end, there is a small Tensioner Arm which serves as a catch for the yellow exit guide. This piece can fall right off of the Inner Cover at this point (see Photo #4).<\/p>\n

Now you can see the Thermistor \/ Thermostat Assembly which is beneath the Inner Cover.<\/p>\n

\"rear\"<\/p>\n

\"rear2\"<\/p>\n

\"rear3\"<\/p>\n

4. Release the front Thermostat<\/strong> (two screws with a #1 Phillips-Head) and pull the Fuser Heat Lamp terminal from the spade lug on the Thermostat (refer to Photo #5).<\/p>\n

5. Mark the position of the Heat Roll Stripper Guide <\/strong>(black plastic). You can mark it using a pen or marker on the metal frame (see Photo #6). The idea is to make it easy to put the part back in the same place later when you go to reassemble everything (if this stripper is riding on the heat roll it will damage it and if it\u2019s too far away, paper jams will result.<\/p>\n

NOTE:<\/span> Steps 6 through 9 will help clear about 3 mm of room for the Heat Lamp to shift towards the rear end of the fuser, which is just enough to free up the lamp\u2019s wires from the metal frame at the front end.<\/p>\n

6. Release the “Connector Holder Frame”<\/strong> which is a small metal frame on the rear end which holds the Main Fuser Connector (refer to the two screws marked “A1” and “A2” on Photo #7). Once that is
\nreleased, you can remove the Fuser CRUM Board, which has a single 30mA pico-fuse on it for resetting the fuser counter.<\/p>\n

7. Next release the black plastic wire guide<\/strong> which is found just below the Connector Holder Frame if you look at Photo #7 (one screw marked \u201cB\u201d).<\/p>\n

8. Also release the Rear Lamp Holder Frame<\/strong> (one screw found approximately where the arrow marked \u201cC\u201d is pointing on Photo #7).<\/p>\n

This piece secures the lamp\u2019s rear ceramic end.<\/p>\n

9. Finally remove the Exit Idler Gear Bracket<\/strong> (two screws marked \u201cD1\u201d and \u201cD2\u201d on Photo #7).<\/p>\n

\"rear4\"<\/p>\n

\"rear5\"<\/p>\n

\"rear6\"<\/p>\n

10. Now, release the Thermistor \/ Thermostat Assembly <\/strong>(five screws with #1 Phillips) and move it so that you can shift the Heat Lamp towards the rear just far enough that the two front blue wires from the lamp will clear the metal frame (see Photo #8).<\/p>\n

11. Take note of how far the Fuser Pressure Screws protrude down below the frame; <\/strong>count threads or mark them so when you reassemble later, you can return the pressure back to where it was. The example fuser which I used to produce this article had 6 threads showing below the frame on both ends. Then back out both Pressure Screws and hinge the Pressure Sleeve Assembly up and off of its hinge pins.<\/p>\n

12. Now the Fuser Heat Roll Assembly can be lifted out of its cradle.<\/strong> Slide it off of the \u201cFront\u201d end of the Heat Lamp (see Photo #9).<\/p>\n

13. Re-use the existing Heat Roll Bearings.<\/strong> These can be very stubborn; both in coming off of the old roller and going onto the new one. You will need to use large mouth pliers or a similar tool and a hammer to tap the old bearings off (See Photo #10).<\/p>\n

That should do the trick! Happy Repairs everyone! See you all next month.<\/p>\n<\/div>\n","protected":false},"excerpt":{"rendered":"

Xerox 7120 style Fuser Modules Repairing and rebuilding the fusers for the WC-7120, 7125, 7220, 7225 The WorkCentre 7120 series is a group of full color pure-bred Xerox machines which are worthy of our attention. These fellows share a lot of the basic design hallmarks of the 7425 style although they land on a slightly lower pricing level. As is usually the case, the fuser module is an important component which is pricy enough to warrant rebuilding. This fuser is slightly simpler than the 7425 fusers we covered in the past two articles, so I think we can tackle this topic in one article. The 7120 fuser looks very similar to the 7425 style fuser at first glance, and the basic design is pretty close, at least in concept. If you\u2019ve read the 7425 fuser rebuild articles, this procedure will look familiar. In spite of the similar design however, the components don\u2019t cross over for the most part. For example, the Fuser Heat Roller is considerably shorter on the 7120. 7120 style Fuser Module The WorkCentre 7120 and 7125 were released first, and they are joined now by the newer WC-7220 and 7225 models. The fuser module which fits all 4 models is sold under the part number 008R13087 for the 110 volt version (overseas the 220 volt version is 008R13088). It has a stated yield of 80K according to some online sources although the OEM brochure doesn\u2019t say. Pricing online ranges between $350.00 and $500.00. The Fuser Heat Roller isn\u2019t spared in the OEM Parts Book, but thankfully some good compatible Fuser Heat Rollers have recently surfaced which make this fuser rebuildable. Let\u2019s get start by getting oriented– check out Photo #1. The \u201cRear End\u201d is the end with the Heat Roll Drive Gear and the main Fuser Connector. The \u201cOuter Face\u201d is the side which would face you if you were to walk up to the machine to remove the fuser and the \u201cInner Face\u201d is the opposite side. The \u201cTop\u201d is where you\u2019ll find the yellow Fuser Exit Guide. Now let\u2019s get right down to it. PROCEDURE: 1. First remove the \u201cOuter Cover,\u201d held on by two screws. You can use a 5.5 mm nut driver or #1 Philips Head. The screw near the front end also retains a small square cover; take that off now because it will fall off easily. Swing the yellow exit guide all the way open. As you jiggle the Outer Cover off, be gentle at the Rear End, because there are wires going to the Fuser Exit Sensor which is mounted on the Outer Cover (see Photo #2). You will need to raise the rear end off and disconnect the connector from that sensor. 2. Then, remove the small rear end cover which also faces the \u201cOuter Face\u201d (one screw). 3. Next flip the module over and take off the \u201cInner Cover\u201d (three screws – refer to Photo #3). Watch out–near the front end, there is a small Tensioner Arm which serves as a catch for the yellow exit guide. This piece can fall right off of the Inner Cover at this point (see Photo #4). Now you can see the Thermistor \/ Thermostat Assembly which is beneath the Inner Cover. 4. Release the front Thermostat (two screws with a #1 Phillips-Head) and pull the Fuser Heat Lamp terminal from the spade lug on the Thermostat (refer to Photo #5). 5. Mark the position of the Heat Roll Stripper Guide (black plastic). You can mark it using a pen or marker on the metal frame (see Photo #6). The idea is to make it easy to put the part back in the same place later when you go to reassemble everything (if this stripper is riding on the heat roll it will damage it and if it\u2019s too far away, paper jams will result. NOTE: Steps 6 through 9 will help clear about 3 mm of room for the Heat Lamp to shift towards the rear end of the fuser, which is just enough to free up the lamp\u2019s wires from the metal frame at the front end. 6. Release the “Connector Holder Frame” which is a small metal frame on the rear end which holds the Main Fuser Connector (refer to the two screws marked “A1” and “A2” on Photo #7). Once that is released, you can remove the Fuser CRUM Board, which has a single 30mA pico-fuse on it for resetting the fuser counter. 7. Next release the black plastic wire guide which is found just below the Connector Holder Frame if you look at Photo #7 (one screw marked \u201cB\u201d). 8. Also release the Rear Lamp Holder Frame (one screw found approximately where the arrow marked \u201cC\u201d is pointing on Photo #7). This piece secures the lamp\u2019s rear ceramic end. 9. Finally remove the Exit Idler Gear Bracket (two screws marked \u201cD1\u201d and \u201cD2\u201d on Photo #7). 10. Now, release the Thermistor \/ Thermostat Assembly (five screws with #1 Phillips) and move it so that you can shift the Heat Lamp towards the rear just far enough that the two front blue wires from the lamp will clear the metal frame (see Photo #8). 11. Take note of how far the Fuser Pressure Screws protrude down below the frame; count threads or mark them so when you reassemble later, you can return the pressure back to where it was. The example fuser which I used to produce this article had 6 threads showing below the frame on both ends. Then back out both Pressure Screws and hinge the Pressure Sleeve Assembly up and off of its hinge pins. 12. Now the Fuser Heat Roll Assembly can be lifted out of its cradle. Slide it off of the \u201cFront\u201d end of the Heat Lamp (see Photo #9). 13. Re-use the existing Heat Roll Bearings. These can be very stubborn; both in coming off of the old roller and going onto the new one. You will need to use large […]<\/p>\n","protected":false},"author":64,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[1649,1814,1648],"tags":[],"_links":{"self":[{"href":"https:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/posts\/9394"}],"collection":[{"href":"https:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/users\/64"}],"replies":[{"embeddable":true,"href":"https:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/comments?post=9394"}],"version-history":[{"count":3,"href":"https:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/posts\/9394\/revisions"}],"predecessor-version":[{"id":9403,"href":"https:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/posts\/9394\/revisions\/9403"}],"wp:attachment":[{"href":"https:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/media?parent=9394"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/categories?post=9394"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/tags?post=9394"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}