{"id":9011,"date":"2014-01-01T16:14:56","date_gmt":"2014-01-01T21:14:56","guid":{"rendered":"http:\/\/www.enxmag.com\/twii\/?p=9011"},"modified":"2014-11-01T16:23:40","modified_gmt":"2014-11-01T20:23:40","slug":"xerox-7120-style-drum-cartridges","status":"publish","type":"post","link":"http:\/\/www.enxmag.com\/twii\/tech-tip\/2014\/01\/xerox-7120-style-drum-cartridges\/","title":{"rendered":"Xerox 7120 style Drum Cartridges"},"content":{"rendered":"

Repairing and rebuilding the Drum Cartridges for the WC-7120, 7125, 7220, 7225<\/strong><\/p>\n

The WorkCentre 7120 style continues to prove itself as a popular series. We took on the fusers a few months back and now it\u2019s time to have a look at the drum cartridges. We\u2019ll take one apart and see what makes it tick. Especially important is how to replace the Drum Reset CRUM chip which resets the counter. This is how you can maximize the yield on the cartridge if it is still making good copies when it times out.<\/p>\n

These machines use 4 drum cartridges which are referred to as \u201cSmart Kits.\u201d There is one for each color position: Black = 013R00657, Yellow = 013R00658, Magenta = 013R00659, and Cyan = 013R660. These drum cartridges include the drum, charge roll, and drum cleaning section in one half of the cartridge, and a developer station on the other half of the cartridge (thus the necessity of having 4 different cartridges so the right color developer is in each). The drums, blades, charge rolls, and charge cleaning rolls are all the same in each color cartridge, but the Drum Reset CRUM chip is unique to each color.<\/p>\n

The stated yield for these drum cartridges is 51K pages for the color drum cartridges and 64K pages for the black drum cartridge.<\/p>\n

So far, as of the publishing time of this article, we have seen drums and CRUMs already available, but nothing else yet. That is likely to change over the next few months as the demand for drum cartridge parts increases. The fact that there is a developer station on the cartridge makes it a trickier cartridge to tackle. Eventually parts distributors will need to find replacement developer and seals as well as all of the other parts involved in rebuilding one of these guys.<\/p>\n

Let\u2019s get into the disassembly of the cartridge. We\u2019ll start by going far enough to replace the CRUM chip which is needed to reset the drum count for the machine. Then we\u2019ll go further into it and replace the drum, charge roll, cleaning roll and cleaning blade. The developer half of the unit will have to wait for a future article when more information and materials are available.<\/p>\n

\"xerox\"<\/p>\n

\"xerox2\"<\/p>\n

\"xerox3\"<\/p>\n

\"xerox4\"<\/p>\n

You will find the Drum Reset CRUM on the rear end underneath the drum cartridge.\u00a0 Remember each color drum cartridge has its own unique CRUM (they\u2019re not interchangeable), so order the correct one.<\/p>\n

    \n
      \n
    1. )\u00a0 To get to the CRUM, you will first need to remove the toner feed shutter.\u00a0 Take off 3 screws (see photos # 1 & 2).\u00a0 Also remove the rear spring which helps keep the two halves of the cartridge together.\u00a0 Finally there is a very stubborn clip in the lower left corner of the toner feed shutter (if you have the cartridge flipped over with the CRUM facing up as shown in Photo #1, the clip is on your right).\u00a0 The way the clip is built around a corner piece makes it seem like it may be necessary to break part of the clip in order to release it.\u00a0 Our example cartridge\u2019s clip was broken in the process of trying to release it, and we found that even so, the clip still seated and with the 3 screws to hold it, it was of no consequence that the clip broke.<\/li>\n<\/ol>\n<\/ol>\n

       <\/p>\n

        \n
          \n
        1. )\u00a0 With the shutter out of the way, you can slide the black plastic CRUM cover off towards the rear. It is a black piece with 4 gold contact points (see photo #3).\u00a0 Then the CRUM will slide off easily enough.<\/li>\n<\/ol>\n<\/ol>\n

           <\/p>\n

            \n
              \n
            1. )\u00a0 Next we\u2019ll go the front end of the cartridge to get ready to separate the developer half of the cartridge from the drum half.\u00a0 Remove 2 screws from the front cover of the developer housing half (see photo # 4) where it says \u201cR3.\u201d R3 is the Magenta cartridge which is what we used for this write up; yours might say R1, 2, 3, or 4 depending on which color drum cartridge you\u2019re working on.\u00a0 Also remove one spring and finally release 2 clips (one at the top right and one at the lower right corner).\u00a0 CAREFUL!\u00a0 When you extract this cover, it releases the developer half of the cartridge from the drum half on the front end (see photo #5), and if you then slide the developer half forward towards you, it will unseat from the drum half at the rear end where the main drive gear shaft seats into a collar. Be careful because all of the gears on the developer half can fall right off of their shafts at this point.<\/li>\n
            2. )\u00a0 Now we\u2019ll concentrate on the drum half of the cartridge (see photo #6).\u00a0 Pull firmly on the Front Drum Bushing (see Photo #8). It is the piece with the silver band around it.\u00a0 It is held by a pair of anchor hooks, but if you pull firmly and rock it a little, it will unseat without too much of a fight.\u00a0 Take note of where the 2 anchors were located so you can reassemble it easily later.\u00a0 Next, go to the rear of the drum.\u00a0 Remove 2 screws from the rear end to release the rear Drum Bushing \/ Shaft (see photos #9 & 10). It will slide out a bit giving room for the drum to lift out of the rear end cradle.\u00a0 Lift the drum out.<\/li>\n<\/ol>\n<\/ol>\n

               <\/p>\n

                \n
                  \n
                1. )\u00a0 With the drum out of the unit, you can remove the drum cleaning blade (2 screws) and clean the waste toner auger behind the blade carefully. Be very gentle with the Mylar recovery.<\/li>\n<\/ol>\n<\/ol>\n

                   <\/p>\n

                    \n
                  1. )\u00a0 You can now lift the charge roller out. Avoid touching the surface of that roll, as finger prints will cause copy quality problems.\u00a0 The black cradle \/ contact for the charge roll is conductive plastic and it can use a little conductive grease.\u00a0 You can lift it out to help you get the cleaning roll out of the unit as well.\u00a0 There\u2019s also something called a \u201cDischarge Lamp\u201d in the drum half of the cartridge, which in truth is just a light-bar which gets illuminated by an LED in the machine.<\/li>\n<\/ol>\n

                     <\/p>\n

                    We\u2019ll need to look closer at the developer half in the future when replacement developer and seals for the developer charge compartment become available.\u00a0 When a new cartridge is installed, there are seals which are extracted from the front end by the customer. Since my sample cartridge was actually a new cartridge you can see the yellow seals present in the photos.<\/p>\n

                     <\/p>\n

                    \"7120

                    7120 Copier<\/p><\/div>\n

                    One of the pull seals releases the shot of developer so it can drop down into the chamber behind the developer mag roller, and a second seal drops a small charge of toner to start the feed auger out, so it doesn\u2019t take too long for toner to find its way to the developer mixing area of the unit.<\/p>\n

                    Until replacement seals are available, shipping a used cartridge would not work because the developer would get everywhere. This procedure is only useful for \u201con-site\u201d or \u201chand deliver\u201d situations.\u00a0 <\/span><\/p>\n

                    Happy New Year everyone!\u00a0 May 2014 be a wonderful year for you and those close to you.\u00a0 And Happy Reconditioning!<\/p>\n

                    \n","protected":false},"excerpt":{"rendered":"

                    Repairing and rebuilding the Drum Cartridges for the WC-7120, 7125, 7220, 7225 The WorkCentre 7120 style continues to prove itself as a popular series. We took on the fusers a few months back and now it\u2019s time to have a look at the drum cartridges. We\u2019ll take one apart and see what makes it tick. Especially important is how to replace the Drum Reset CRUM chip which resets the counter. This is how you can maximize the yield on the cartridge if it is still making good copies when it times out. These machines use 4 drum cartridges which are referred to as \u201cSmart Kits.\u201d There is one for each color position: Black = 013R00657, Yellow = 013R00658, Magenta = 013R00659, and Cyan = 013R660. These drum cartridges include the drum, charge roll, and drum cleaning section in one half of the cartridge, and a developer station on the other half of the cartridge (thus the necessity of having 4 different cartridges so the right color developer is in each). The drums, blades, charge rolls, and charge cleaning rolls are all the same in each color cartridge, but the Drum Reset CRUM chip is unique to each color. The stated yield for these drum cartridges is 51K pages for the color drum cartridges and 64K pages for the black drum cartridge. So far, as of the publishing time of this article, we have seen drums and CRUMs already available, but nothing else yet. That is likely to change over the next few months as the demand for drum cartridge parts increases. The fact that there is a developer station on the cartridge makes it a trickier cartridge to tackle. Eventually parts distributors will need to find replacement developer and seals as well as all of the other parts involved in rebuilding one of these guys. Let\u2019s get into the disassembly of the cartridge. We\u2019ll start by going far enough to replace the CRUM chip which is needed to reset the drum count for the machine. Then we\u2019ll go further into it and replace the drum, charge roll, cleaning roll and cleaning blade. The developer half of the unit will have to wait for a future article when more information and materials are available. You will find the Drum Reset CRUM on the rear end underneath the drum cartridge.\u00a0 Remember each color drum cartridge has its own unique CRUM (they\u2019re not interchangeable), so order the correct one. )\u00a0 To get to the CRUM, you will first need to remove the toner feed shutter.\u00a0 Take off 3 screws (see photos # 1 & 2).\u00a0 Also remove the rear spring which helps keep the two halves of the cartridge together.\u00a0 Finally there is a very stubborn clip in the lower left corner of the toner feed shutter (if you have the cartridge flipped over with the CRUM facing up as shown in Photo #1, the clip is on your right).\u00a0 The way the clip is built around a corner piece makes it seem like it may be necessary to break part of the clip in order to release it.\u00a0 Our example cartridge\u2019s clip was broken in the process of trying to release it, and we found that even so, the clip still seated and with the 3 screws to hold it, it was of no consequence that the clip broke.   )\u00a0 With the shutter out of the way, you can slide the black plastic CRUM cover off towards the rear. It is a black piece with 4 gold contact points (see photo #3).\u00a0 Then the CRUM will slide off easily enough.   )\u00a0 Next we\u2019ll go the front end of the cartridge to get ready to separate the developer half of the cartridge from the drum half.\u00a0 Remove 2 screws from the front cover of the developer housing half (see photo # 4) where it says \u201cR3.\u201d R3 is the Magenta cartridge which is what we used for this write up; yours might say R1, 2, 3, or 4 depending on which color drum cartridge you\u2019re working on.\u00a0 Also remove one spring and finally release 2 clips (one at the top right and one at the lower right corner).\u00a0 CAREFUL!\u00a0 When you extract this cover, it releases the developer half of the cartridge from the drum half on the front end (see photo #5), and if you then slide the developer half forward towards you, it will unseat from the drum half at the rear end where the main drive gear shaft seats into a collar. Be careful because all of the gears on the developer half can fall right off of their shafts at this point. )\u00a0 Now we\u2019ll concentrate on the drum half of the cartridge (see photo #6).\u00a0 Pull firmly on the Front Drum Bushing (see Photo #8). It is the piece with the silver band around it.\u00a0 It is held by a pair of anchor hooks, but if you pull firmly and rock it a little, it will unseat without too much of a fight.\u00a0 Take note of where the 2 anchors were located so you can reassemble it easily later.\u00a0 Next, go to the rear of the drum.\u00a0 Remove 2 screws from the rear end to release the rear Drum Bushing \/ Shaft (see photos #9 & 10). It will slide out a bit giving room for the drum to lift out of the rear end cradle.\u00a0 Lift the drum out.   )\u00a0 With the drum out of the unit, you can remove the drum cleaning blade (2 screws) and clean the waste toner auger behind the blade carefully. Be very gentle with the Mylar recovery.   )\u00a0 You can now lift the charge roller out. Avoid touching the surface of that roll, as finger prints will cause copy quality problems.\u00a0 The black cradle \/ contact for the charge roll is conductive plastic and it can use a little conductive grease.\u00a0 You can lift it out to help you get the cleaning roll out of the unit […]<\/p>\n","protected":false},"author":64,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":[],"categories":[1649,1814,1648],"tags":[],"_links":{"self":[{"href":"http:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/posts\/9011"}],"collection":[{"href":"http:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/users\/64"}],"replies":[{"embeddable":true,"href":"http:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/comments?post=9011"}],"version-history":[{"count":6,"href":"http:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/posts\/9011\/revisions"}],"predecessor-version":[{"id":9024,"href":"http:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/posts\/9011\/revisions\/9024"}],"wp:attachment":[{"href":"http:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/media?parent=9011"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/categories?post=9011"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.enxmag.com\/twii\/wp-json\/wp\/v2\/tags?post=9011"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}